Author Archives: Eric Gomez
Author Archives: Eric Gomez
Don’t you hate it when you’re ready for a nice, cold drink and your refrigerator refuses to give you any ice cubes? In this article, we’ll be looking at dealing with a refrigerator repair with Las Vegas Appliance Masters (http://lasvegasappliancemasters.com) to help us get our ice maker working again.
Complaints: The icemaker no longer producing ice.
Diagnosis: Cutting Grid is not operating properly. There is a break in the wire of the cutting grid. Therefore the cutting Grid needs to be replaced.
Warning – Before beginning any repairs always disconnect the power to the appliance. It is also recommended to test the outlet for proper voltage. Remember to also turn off the water.
Tools needed: ¼” Nut driver and ¼” Socket and Ratchet.
Removing the Grid Cutter (2313637)
To access the cutting grid the first thing you want to do is to remove the two ¼” screws on the cover piece. Then we are just going to go ahead and slide the cover off. Right at the front will be our cutting grid, and as you can see the broken wire.
The first thing we are going to do is to go ahead and disconnect the power connector for the grid. The power connector for the grid is two black wires. And we have two screws at the side, so we are going to go ahead and remove the screws.
We are now going to disconnect the harness for the temperature sensor. Just to get that out of the way. Then we are just going to go ahead and take the grid out. There is also a harness on the back side, disconnect it and then go ahead and remove the grid.
Now we are going to go ahead and remove the classic sleeve, for the old unit and insert it onto the cutting grid of the new grid and that is inserted into the right hand side.
Installing the new Grid Cutter (2313637)
Slide it into the slut and attach the harness on the back side that needs to be reconnected. Make sure that the wiring runs on the outside of the cutting grid. You don’t want the wire to touch the cutting grid. Then you can go ahead and insert the long screws, that is the one the goes in with the sleeve, put both half way in with your hand first, then use the ratchet to finish screwing in the screws.
You don’t want to over tighten the screws because they are going into plastic. Then we are going to go ahead and capture the bin sensor harness and then make sure your wiring stays on the outside of the cutting grid. Then we are going to connect the harness for the cutting grids itself, make sure that it is position off to the side and put the cover back on. Get this started by hand, put screws in half way then tightened.
The icemaker was turned off, so go ahead and turn the power back on. At this point the water is filling up, it will just have to run some cold water over the unit to freeze the ice cubes and then it is going to dump it over the cutting grid. The cutting grid should cut the cubes and this should drop into the bottom. So that is going to complete our repair.
Today I am going to show you how to remove an oil stain from concrete. This is a common problem, especially if you own an older car or, like us, because of having many short term tenant rentals (ours are managed by the folks at www.extendedstay-tucson.com and we love them!), you’re never sure what kind of car might be parking in your driveway or garage and you always end up with stains after a while. So I compared four different methods. Some worked, some didn’t. So you are going to want to stay tuned because you are going to save time and money in the process. Let’s get started. I tried four different methods. I used kitty litter, TSP, WD-40, and Drylok Etch.
So I wanted to see which one would work best at removing the stain – the oil stain or whatever stain it is – in the concrete. I used to kitty litter first. And this is a real basic method. All you do is pour the kitty litter onto the stain and then mash it real good with your body weight. Now, you don’t have to wear green shoes like I did, but mash it really good and then you sweep it off the stain and I did not see any change.
That’s not to say that this method wouldn’t work for you, so give it a shot. The second one was using WD-40. All I did here was spray the WD-40 onto a little circular section of the stain, because after all, this is an experiment, and I did not want to try it on the whole section, I sprayed it on, and then I scrubbed it really good with a stiff wire brush. I did this for several minutes and after that, I brushed on some kitty litter to absorb the WD-40 and hopefully the stain. And I let that sit there for a good 10-15 minutes.
In the meantime, I took some straight TSP and I poured that over the adjacent stain like so. And again, I used a stiff wire brush to hopefully scrub out the stain. And this is what it looked like, I put some kitty litter to absorb the stain. So I brushed off the WD-40 and again, nothing. So WD-40 is a bust. Then here is a surprise. I shoveled off the kitty litter that absorbed the TSP, and there there was a noticeable difference. So TSP is a good method to try on an oil stain.
The forth method that I used was Drylok Etch. Be safe when you use all these chemicals, wear gloves, safety glasses. And what I did is I scrubbed it with a stiff wire brush and this is what it looked like. So it turned out really awesome with the Drylok Etch. And as a reminder, this is what it looked like before. So Drylok Etch, awesome. There you have it. The kitty litter and the WD-40 didn’t work out as well for me as maybe, it might for you.
You could give it a shot, especially if you own a cat, which I don’t. I went out and bought the kitty litter. That’s a whole different story. And most everybody’s got WD-40. But the TSP and the Drylok Etch were total winners. And I would say try the TSP first, then go for the Drylok Etch. But there you have it. Those are two solutions that will help you out with removing your oil stain from concrete.
I hope this helped you out. Here’s some more info from YouTube…
Among the most effective home improvements when selling your house you can do is to replace the old and worn-out carpets. This is going to make the property look nice and give a great impression on prospective buyers. Buyers fast get turned off if they think that they’re going to must replace the stained and tattered carpets in every room.
Spackle and then paint holes to get rid of them. Go to your local home improvement store like Lowe’s or Home Depot to purchase the spackle. Use a quite small number in the event that you will need to fill miniatureThe little holes might be filled with spackle using only a bobby pin. Use pretty much anything with a straight, hard edge or an old credit card to smooth the dehydrated spackle. Then you have to paint. The holes will evaporate.
Clean up the outside of your house. All it takes to make your home look and feel better is a little TLC on the outside. Trim the shrubs and pull the weedsof the flower bed. Add some cosmetic landscape lighting and be sure that all the outside light fixtures are in proper working order.
The outside of your home also makes a superb spot for a home improvement job. Staining your drive adds a lovely touch to the very front of your dwelling. Additionally, look to see whether you have to fill any cracks or re-tar the driveway. Occasionally, the front of your home could be forgotten as you make improvements, but these projects can really add a lot to the aesthetic value of your property.
Decals are an excellent facelift for appliances and boring furniture; getting them off is a different narrative. The subsequent tip is positive to aid in the event you’re out of ideas on the best way to remove old stickers from surfaces. Spray on the decals you wish to remove with WD 40 spray. Attempt to lift the edges to get the liquid. Let it sit in the solution for a minute or two and after that gently scrape the sticker with an old credit card or a plastic knife.
Consider the effect on the resale value of your home’s before you embark on a home improvement job. For example, converting your garage into a living room may make sense for your immediate needs, but this type of addition turns off a lot of home buyers. Conditions can change even should you not plan on selling immediately, and you may have to spend additional cash getting your home back to the way it was.
Consider converting fresh rooms in your house. Seriously look at what you need to work with, before you spend too much money adding an additional room or two to your home. Are you getting much use out of that exercise office or room? Storage spaces like attics can be transformed into something useful, like a bedroom.
Enhance your house by removing items you don’t want. You will have more space as well as your home will appear to be larger. De-mess by donating unneeded things for example clothes, furniture, etc., keeping or throwing away Even packing your stuff away in boxes and putting those in the attic will remove things from your immediate living place.
Plenty of houses have wall to wall carpeting that is stained and looks bad. offer lasting appeal and more durability than carpeting can provide. With these tricks, you can work smarter-not harder. Shortly your house is going to be a stunning showplace. You’ll notice live in a home that’s more wonderful than you ever could have imagined.
Do your own homework in case you can not manage a professional designer. Review on-line resources, publications and magazines . You never know where you will find an image that can determine the future of your renovations. Literature may also provide you with the info that you need to get your project done.
Making home improvements and easy home repairs is a terrific thought for making your house and raising the value of your home a more pleasant location, but additionally, it may be a catastrophe if done wrong. Needing to mend your home improvements with additional developments can be avoided with a little thought and effort. Use the below hints to practice the right mindset to make sure all your home improvements are successful.
Keep family and your house safe by properly installing a smoke detector in your home. Smoke detectors find unsafe and hazardous smoke before you do. Stay in the safe side and buy a new smoke detector. Be sure to check the batteries each month to make sure that it’s functioning accurately when disaster strikes.
Give a fast update to your kitchen by wiping down the cupboards and adding or altering the . Handles or giving your kitchen cabinets a brand new set of knobs really can improve the look of your kitchen without costing a lot of money. With all these styles of knobs and handles accessible, you can alter the nature of your kitchen easily and quickly.
In the event you want your living room or dorm to have a contemporary clean feel to it, choose to purchase a couch with long, lean lines and nominal cushioning. Select the couch in a bold color like red, black, or beige to make an impression in your region. You can dress it up with striped ornamental pillows or some zebra print.
One custom which is good for keeping your home improvement project, is setting aside a particular budget for upgrades and repairs. Homeowners who allocate a certain sum of money for such endeavors will probably be better at maintaining their dwellings. In the event you don’t use all your budget, carry it around to the following year.
As with any repair, be sure you unplug the appliance before beginning. Your first step is to remove the screws at the rear of the control panel to release it. Next open the dryer door and remove the screws inside the door frame which secure the main top. Carefully unhook the control panel tabs from the mail top and lift up the top and remove. Uninstall the screws, securing the front panel.
Lift the front panel up and rotate it to the side. Remove the screw or screws, securing the sides of the cabinet to the support panel. Reach under the drum and push the idler pulley to release the tension on the belt, then unthread the belt from the pulley and motor shaft. Use the belt to help lift out the drum. Next disconnect the motor wire harness as well as the belt switch wires.
Disconnect the power cord connector and the door wires before you start any kind of repair. If applicable, move the switch guard out of the way. After noting their position, disconnect the door switch wires. Now feed the wires through the support panel. Remove the screws, securing the motor grounding wire. Next remove the screws, securing the cycling thermostat and move the thermostat out of the way (you can learn more about replacing appliance parts from our friends at Appliance Masters by clicking here: http://appliancerepairtucsonaz.org).
Uninstall the screws on the back of the motor mounting bracket and the screws at the front of the support panel. Move the wires out of the way, slide the blower wheel and motor assembly out of the housing and detach the idler arm. Now remove the blower wheel and motor from the cabinet and set it on a sturdy surface. Use pliers to secure the motor shaft as you rotate the blower wheel counterclockwise to remove.
Be aware, this may require some effort. Now remove the screws from the front bracket. Use a flat head screwdriver to remove the rear mounting clip. Noting the orientation of the old motor, remove it from the mounting bracket. You are now ready to install the new motor. Correctly position the new motor on the mounting bracket. Snap the rear mounting clip into place and secure the screws in the front bracket.
Replace the blower wheel by threading a clockwise onto the motor shaft. Secure the shaft as you tighten the wheel. Return the motor and blower wheel assembly to the cabinet. Reattach the idler arm and slide the assembly into the housing. Confirm that the idler arm correctly activates the belt switch. Feed the wires back into position. Replace the screws securing the assembly to the support panel and the one securing it to the mounting bracket.
Replace the screw to secure the grounding wire. Position the cycling thermostat on the blower housing and secure the screw. Feed the door wiring harness through the support panel. Reconnect the door switch wires. Reposition the switch guard if necessary and reconnect the door wire connector. Reconnect the power cord connector. Reconnect the belt switch wires and the motor wire harness.
Replace the drum in the cabinet by aligning the drum shaft and bearing with the bearing retainer on the rear panel. Reach under the drum and thread the belt onto the pulley and motor shaft in a zigzag formation. Now rotate the drum to help align the belt. Replace the screw or screws, securing the sides of the cabinet to the support panel. Reposition the front panel by first aligning the tabs in the base with the slots in the panel.
Now lift up the drum and snap the front panel into place. Secure the screws. Replace the mail top by aligning the slots in the top with the tabs on the frame, then reinstall the screws in the door frame to secure. Reposition the control panel by inserting the tabs into the slots at the back of the main top. Replace the screws in the back to secure. You are now ready to plug the power cord back in and confirm that the appliance is functioning properly.